Choose Language: Japanese Korean Spanish Russian German French Portuguese Arabic Italian
我的账号 购物车
 
Product Categories
如何使用VAMO V5可变电压/功率MOD  
        The new Vamo V5 Variable Voltage/Wattage MOD is sleek, powerful, reliable, full VAMO V5 kitfeatured and very well built with the same features as the V3 but body of the V2. Voltage or Wattage is variable 3.0-6.0volts or 3.0-15.0watts respectively, using a single 18350 or with the included extension tube you can run a single 18650, or one/two 18350 lithium-ion rechargeable batteries, (all available separately). Check atomizer/clearomizer/cartomizer resistance and battery voltage too with long press of the small buttons.

            The new VAMO V5 Variable Voltage/Wattage MOD is single mode which provides RMS voltage monitoring. The RMS mode is more accurate because it samples the output Voltage repeatedly while it is powering an atomizer or cartomizer. With its 5 Amp output, it has ample power to run whatever device you want.

           The buttons and settings are easy to figure out. This version has stainless buttons and easy to read OLED display. VAMO V5 Variable Voltage/Wattage MOD is completely compatible with the eGo series atomizers/cartomizers/clearomizers.

 

How to setup the VAMO V5 function

 

VAMO V5 Variable Voltage/Wattage MOD Function:

 

1. Output voltage from 3.0V to 6.0V, adjusting the working Volt 0.1V each time by pressing “+” or “-” buttons.
2. Output power from 3.0W to 15.0W, adjusting the working wattage 0.5W each time by pressing “+” or “-” buttons.
.3. Keep pressing the “+” button more than 3seconds, LCD screen displays the present working resistance.
4.Keep press the “+” and the “-” button for 3 seconds, LCD screen displays” 1.Pwer Voltage”, or “2.LCD Display” or “3.LCD ON/OFF”.
5.Max Armature Current 5A.
6. 5-clicks safety cutoff: 5 clicks on Power button, LCD screen displays" system: ON" or "system: OFF". This is a very convenient option if you typically carry your device  in your pocket or purse.
7.Revese battery protection keeps circuit safe if the battery is installed backward.
8.Battery Monitoring shuts the unit off once battery has reached end of the charge.
9.Amperage limited system protects against over current situations.
10.Thermal Monitoring shut the device off if it detects a high temperature condition.
11. Fit atomizers with resistance 1.5-5.0 Ohms.
12. Time limit protection function. It will shut down with more than 10s each puff.
13. LCD  displays “ Low load” if resistance lower than 1.2 Ohms, “ Low V” if the battery needs to charge.

 

How to use VAMO V5 Variable Voltage/Wattage MOD?

 

-1. On/Off:  click the power button 5 times to turn on the VAMO V5 and 5 times again to  turn off the VAMO V5.
--2. Set the control Panel: 
Press and hold down the” +” and” - “ buttons at the same time for 5 seconds to enter the Menu. Press the “+” button, adjust the main menu, and press the “-” button adjust the submenu, 3 seconds without any operation to exit the menu.

 

VAMO V5 menu

 

-3. Work: Screw and connect the eGo series atomizer/clearomizer(eGo, eGo-T, eGo-C, eGo-W CE4/CE5/CE6, Protank, H2, ect.) with the VAMO V5, then they will be stand-by state, it  works only when you press the VAMO V5  power button. Press the power button and inhale at the same time.
--4. Low load: When the working resistance is under 1.2 Ohms, pressing the power buton, the LCD screen display “Low load”
--5. Low V: If the battery voltage is less than 3.2V, the LCD screen will display “Low V”
--6. Short out: When the VAMO V5 is short out, the LCD screen will display “ Short”
--7.Battery Charging:
The VAMO V5 can’t use an ego battery charger to charge. You should take out the 18350/18650 battery to charge. When the indicator light is red, the device is charging. When the light turns green, charging is complete.

 Attention: It can not be charged from the battery screw.

How to use VAMO V5 manual

Please click for what suitable voltage to different the atomizer/ clearomizer/ cartomizer?

 

What atomizers/cartomizers can used in the VAMO V6 Variable Voltage/Wattage MOD?

 

The VAMO V6 Variable Voltage/Wattage MOD comes with 510/eGo threading connector, compatible with 510 and eGo threaded atomizers/clearomizers/cartomizers with resistance (1.5-5.0ohm). For examples: eGo-T atomizers, eGo CE4 cartomizers, eGo CE5 cartomizer , eGo CE6 cartomizer, eGo Mini Protank Glassomizer, eGo H2 Clearomizer, eGo-C atomizer, eGo-W cartomizers, 510 atomizers, eGo atomizers, 510 MEGA atomizer, eGo MEGA atomizers, 510 cartomizers, eGo cartomizers, eGo type A atomizers, Nautilus BDC Adjustable Airflow Clearomizer, Aerotank MEGA clearomizer, ect.

Talk with me